Why is my Amana washer not spinning?

Common reasons include a worn drive belt (about 40 %),a faulty lid switch (about 25 %),a failed motor-coupling (about 20 %),or other internal mechanical/electrical issues.

Amana washer is not spinning

When your Amana washer is not spinning, it can throw your whole laundry day into chaos. For those who rely on their washing machine to keep household routines running smoothly, this issue can be frustrating and time-consuming.

In this guide, we’ll walk you through the most common reasons why your Amana washer might stop spinning, how to troubleshoot the problem at home, and what to do if you need expert assistance. Whether the fix is simple or requires professional help, you’ll find the answers you need right here.

Key reasons for the problem:

40% of reported issues are the

Worn-Out Drive Belt

25% of reported issues are the

Faulty Lid Switch

20% of reported issues are the

Motor Coupling Failure

15% of reported issues are the

All Other Causes

One Plan. Every Appliance. Zero Stress.

Extended warranties only cover one item. Liberty Home Guard protects all your appliances and systems under one simple plan.
If it breaks, we’ve got you covered—no matter the brand.

Get My Free Quote

Diagnostic and troubleshooting steps

Amana washer not spinning? Follow the steps below to troubleshoot common causes like a worn drive belt, faulty lid switch, or motor coupling failure.

Step 1:

Check for Overloading or Unbalanced Loads

Pause the cycle and open the lid.
Redistribute the load evenly around the drum.
Remove a few items if the washer is too full.
Resume the spin cycle to see if the issue is resolved.

Step 2:

Inspect the Lid Switch or Door Latch

Close the lid firmly and listen for a clicking sound.
If there’s no click, the lid switch may be faulty.
Use a multimeter to test for electrical continuity if you’re comfortable.
Replace the switch if necessary with a model-specific part.

Step 3:

Examine the Drive Belt

Unplug the washer and remove the rear or bottom access panel.
Inspect the belt for signs of wear, fraying, or snapping.
If the belt is loose or broken, replace it with an Amana-compatible replacement.

Step 4:

Test the Motor Coupling or Clutch Assembly

Access the coupling by removing the cabinet and pump.
Check for broken plastic components or worn rubber bushings.
Replace the motor coupling if any parts are visibly damaged.

Step 5:

Check for Drainage Issues

Inspect the drain hose for kinks, clogs, or blockages.
Clean out the drain pump filter if your model has one.
Run a drain and spin cycle to test functionality.

Step 6:

Reset the Washer’s Control Panel

Unplug the washer for 1–2 minutes.
Plug it back in and open/close the lid six times within 12 seconds to reset some Amana models.
Start a new cycle and check for proper spinning.

Step 7:

Inspect the Timer or Control Board

Look for blinking lights or error codes on the control panel.
Consult your user manual for interpretation.
If the board is not responding, it may need replacement—this repair is best handled by a technician.

Key actions for homeowners:

Make sure the lid or door is fully closed and latched before starting a cycle.
Avoid interrupting cycles once they’ve started.
Clean the washer drum and drain pump filter regularly.
Check the hoses for wear, leaks, or kinks.
Schedule annual inspections or maintenance.

Most common repairs needed to fix an amana washer

When your washer isn't spinning, certain repairs are more commonly required than others. Below are the most frequent fixes:

Replace the Lid Switch Assembly: Use a multimeter to test for continuity. If the switch fails the test or shows visible damage, replace it with a model-specific OEM part. This is a relatively simple DIY job using basic tools.
Realign or Replace the Lid Strike: Inspect the strike for damage and proper alignment. If it’s bent or cracked, install a new one and ensure it lines up properly with the lid switch.

Frequently Asked Questions

Why is my Amana washer not spinning even though it is filled with water?
If your washer fills but doesn’t spin, the issue could be a faulty lid switch, worn drive belt, broken motor coupling, or a problem with the control board. These components play key roles in
Can an unbalanced load cause my Amana washer to stop spinning?
Yes, an unbalanced or overloaded drum can prevent your washer from spinning. This happens when bulky or unevenly distributed laundry causes the washer to stop the spin cycle for safety. Try redistributing the load evenly and restarting the cycle.
How do I reset my Amana washer when it won't spin?
To reset most Amana washers, unplug the washer for 1 to 2 minutes before plugging it back in. Open and close the lid six times within 12 seconds (for top-load models). Then, start a new wash cycle. This can help clear any glitches in the washer’s control system.
Should I repair or replace my Amana washer if it stops spinning?
If your washer is under 10 years old and the issue is with a single component like the lid switch, drive belt, or motor coupling, it’s usually worth repairing. However, if multiple components are failing or the washer is near the end of its lifespan, replacing it might be the more cost-effective option—especially if repair costs are high.

Want to view more?

Amana washer is not turning on

The Most Consumer Centric
Home Warranty Provider.

Homeowners across the country recommend Liberty Home Guard Home Warranty above all others.
Don’t just take our word for it—Liberty Home Guard Reviews speak for themselves!

I've had this home warranty service ...

I've had this home warranty service for over a year. I've exclusively used the "pick a contractor" option and have had good result...

Omar K.

I was expecting so so service and re...

I was expecting so so service and repair, but that was not the case. The over the range microwave door stopped closing. I put in a...

Alice N.

JP was extremely professional, frien...

JP was extremely professional, friendly, and efficient throughout the entire process. He communicated clearly, handled everything ...

Donald P.

E Perach is the most understanding h...

E Perach is the most understanding helpful home warranty professional I’ve ever dealt with after have 3 other companies. Her cus...

Michael F.

The support-person was very knowledg...

The support-person was very knowledgeable and gave me the information I needed to make my decision. Suppoet-person was Tony Torres...

John M.

Great job. Would highly recommend th...

Great job. Would highly recommend the technician!! And fast: our dryer needed repair on a Friday and by the following Tuesday we h...

Larry F.

Representative was very knowledgable...

Representative was very knowledgable and friendly. This is the second call about an issue and Tony was extremely patient and helpf...

JoAnn W.

Maia Palmer was the most helpful rep...

Maia Palmer was the most helpful representative I have spoken with at Liberty Home Guard. They took care of my claim with compassi...

May D.

I'm so glad I switched to Liberty. T...

I'm so glad I switched to Liberty. They were quick to respond to my request and covered the work that needed to be done.

Debra D.

I have Liberty Home Guard for an yea...

I have Liberty Home Guard for an year. I worked with Ronald Moran. He is an awesome service representative. From the point I open ...

Vidyasagar U.