Maytag washer not filling

A Maytag washer that isn’t filling with water can disrupt your laundry routine and leave you frustrated. There are various reasons why this problem occurs, from water supply issues to faulty components within the washer itself. Thankfully, most of these problems are straightforward to diagnose and resolve with the right guidance. Learn about the possible causes of a Maytag washer not filling and get actionable steps to help you get your machine back in working order.

Key reasons for the problem:

50% of reported issues are the

Water Inlet Valve

30% of reported issues are the

Pressure Switch

15% of reported issues are the

Control Board

5% of reported issues are the

All Other Causes

Diagnostic & troubleshooting steps

Is your Maytag washer not filling with water? This step-by-step guide covers everything from water inlet issues to electrical components, offering practical solutions and when to seek professional help.

Step 1:

Check the Water Supply

Ensure both hot and cold water supply valves are fully open.
Inspect the water hoses for kinks or leaks that may restrict water flow.

Step 2:

Clean the Inlet Screens

Turn off the water supply and disconnect the hoses from the washer.
Check the inlet screens inside the water inlet valve for debris or mineral buildup. Use a small brush to clean them.

Step 3:

Test the Water Inlet Valve

If cleaning the inlet screens doesn’t work, the valve itself may be defective. Use a multimeter to test for continuity. Replace the valve if it’s faulty.

Step 4:

Inspect Washer Settings

Double-check that the cycle and water level settings are appropriate for the load. Some cycles, like “Rinse and Spin,” may not fill the washer with water.

Step 5:

Examine the Pressure Switch

If the washer stops filling prematurely, the pressure switch may be malfunctioning. This component may need to be tested and replaced if defective.

Step 6:

Test the Lid Switch (For Top-Loaders)

If your washer has a lid switch, ensure it’s functioning properly. Use a multimeter to test for continuity. Replace the switch if necessary.

Step 7:

Inspect the Hoses

Check the water hoses for clogs or damage. Replace any hose that’s blocked or leaking.

Step 8:

Assess Water Pressure

Confirm your home’s water pressure meets the washer’s requirements (typically 20-120 psi). If the pressure is too low, consult a plumber to address the issue.

Step 9:

Run a Diagnostic Test

Some Maytag washers have a diagnostic mode that allows you to identify error codes. Refer to your user manual for instructions.

Key actions for homeowners:

Check and clean the inlet screens every few months to prevent clogs caused by debris or mineral buildup.
Periodically check water hoses for signs of wear, leaks, or kinks. Replace hoses as needed to ensure proper water flow.
Use high-efficiency (HE) detergent to prevent residue buildup that can interfere with washer performance.
Overloading can strain the washer and its components, potentially leading to malfunctions. Follow the manufacturer’s load size guidelines.
Have your washer inspected annually by a professional to catch and address potential issues early.

Most common repairs needed to fix a maytag washer not filling

When your washer won’t fill, certain repairs are more commonly required than others. Below are the most frequent fixes:

Clean Clogged Inlet Screens: Debris or mineral buildup in the water inlet screens can block water flow. Cleaning them is often a quick fix.
Replace a Faulty Water Inlet Valve: If the inlet valve fails to open or close properly, it may need to be replaced to restore water flow.
Unclog or Replace Water Hoses: Kinked, blocked, or damaged water hoses may need to be cleared or replaced to ensure proper water flow.
Fix Low Home Water Pressure: If the home’s water pressure is insufficient, adjustments to the plumbing system or installing a pressure booster may be necessary.

Frequently Asked Questions

Why is my Maytag washer not filling with water?
Your Maytag washer may not fill due to water supply issues, a clogged inlet screen, a defective water inlet valve, or improper settings. Use the troubleshooting steps above to diagnose and resolve the problem.
How do I clean the water inlet screens on my Maytag washer?
Turn off the water supply, disconnect the hoses, and carefully remove debris from the screens inside the water inlet valve using a brush or toothpick.
Can I fix a Maytag washer that won’t fill on my own?
Yes, many filling issues can be resolved with basic troubleshooting. However, if components like the inlet valve or pressure switch are faulty, professional assistance may be required.
What should I do if my home’s water pressure is too low for the washer?
Contact a plumber to assess and resolve low water pressure issues in your home.

Want to view more?

Maytag washer won’t start cycle

The Most Consumer Centric
Home Warranty Provider.

Homeowners across the country recommend Liberty Home Guard Home Warranty above all others.
Don’t just take our word for it—Liberty Home Guard Reviews speak for themselves!

Camile was very helpful today at Lib...

Camile was very helpful today at Liberty Home Guard. He stayed on the phone with me until the transaction was complete. He explain...

Pennie W

Alex was great of understanding the ...

Alex was great of understanding the situation and act quickly to address my concern great job.

Shedi N

I had the pleasure of speaking with ...

I had the pleasure of speaking with Mishelle Bruno yesterday and she was very professional, patient, knowledgeable about her job, ...

Dee Dee Burks

Very Professional

David H

I received excellent service by both...

I received excellent service by both Liberty and the technician they sent.

Marjorie P

I want to thank the team at Liberty ...

I want to thank the team at Liberty Home Guard and especially John Vasquez, for the exceptional and professional work they do when...

Michel R

Alex was a really good help made my ...

Alex was a really good help made my first claim easy for me , good job

Sergio F

Patient and persistent in getting my...

Patient and persistent in getting my claim processed. Thanks!!

Doc J

Jesus was very polite and handled my...

Jesus was very polite and handled my claim in a precise and timely manner.

Mark C

I have made three claims with Libert...

I have made three claims with Liberty and all have gone well; I always expect it to be a pain because most insurance is, but Liber...

Janna C